CCIE实验室考试指南(6)[1]
来源:学生作业学帮网 编辑:学帮网 时间:2024/06/08 12:40:45 Cisco认证
CCIE实验室考试指南(6)[1]Cisco认证
【网络综合 - Cisco认证】
Lab 06 -
Password Recovery Trouble Shooting
Let us assume that you have a router and you don’t know the enable
secret password.
First and foremost you must have physical access to the router to
perform password recovery. Bit 6 defines if the configuration file will
be loaded from NVRAM. Since there is a password in the configuration
file that we do not know, we will want to set bit 6 to 1.
If bit 6 is 0 then the router will load the configuration file from
NVRAM. If bit 6 is 1 then the router will not load the configuration file
from NVRAM.
Configuration Register represented in Decimal
The following are the steps to recover from a lost password.
1. Turn the router off, turn the router on, and within 60 seconds
issue the break sequence of your terminal emulation package. If
you are using hyperterminal that would be .
2. You will now be in ROM monitor mode indicated by the >
prompt. Our goal here is to turn bit 6 on, so if the configuration
register is set to 0x2102, we want to change the register to
0x2142. To determine the current configuration register setting
use the following command:
>e/s 2000002
To change the register:
>o/r 0x2142
To re-initialize the router
>I
3. After the router prompt appears get into the privileged mode
and copy the backup configuration file to RAM.
4. Get into the configuration mode and key in your new password
5. Change the configuration register back to original setting
6. Perform a no-shut on all interfaces
7. Copy the running configuration to NVRAM
All of the steps are in bold
System Bootstrap, Version 5.2(8a),
RELEASE SOFTWARE
Copyright (c) 1986-1995 by cisco Systems
2500 processor with 16384 Kbytes
of main memory
Abort at 0x10EA87C (PC) break sequence
issued here
>e/s2000002
2000002: 2102 use q to quit the examine mode
>o/r0x214Cisco认证
Lab 06 -
Password Recovery Trouble Shooting
Let us assume that you have a router and you don’t know the enable
secret password.
First and foremost you must have physical access to the router to
perform password recovery. Bit 6 defines if the configuration file will
be loaded from NVRAM. Since there is a password in the configuration
file that we do not know, we will want to set bit 6 to 1.
If bit 6 is 0 then the router will load the configuration file from
NVRAM. If bit 6 is 1 then the router will not load the configuration file
from NVRAM.
Configuration Register represented in Decimal
The following are the steps to recover from a lost password.
1. Turn the router off, turn the router on, and within 60 seconds
issue the break sequence of your terminal emulation package. If
you are using hyperterminal that would be .
2. You will now be in ROM monitor mode indicated by the >
prompt. Our goal here is to turn bit 6 on, so if the configuration
register is set to 0x2102, we want to change the register to
0x2142. To determine the current configuration register setting
use the following command:
>e/s 2000002
To change the register:
>o/r 0x2142
To re-initialize the router
>I
3. After the router prompt appears get into the privileged mode
and copy the backup configuration file to RAM.
4. Get into the configuration mode and key in your new password
5. Change the configuration register back to original setting
6. Perform a no-shut on all interfaces
7. Copy the running configuration to NVRAM
All of the steps are in bold
System Bootstrap, Version 5.2(8a),
RELEASE SOFTWARE
Copyright (c) 1986-1995 by cisco Systems
2500 processor with 16384 Kbytes
of main memory
Abort at 0x10EA87C (PC) break sequence
issued here
>e/s2000002
2000002: 2102 use q to quit the examine mode
>o/r0x214Cisco认证